XTi 6002 Power Amplifier Specifications:

• Stereo, 2 ohms (per ch.): 3000W
• Stereo, 4 ohms (per ch.): 2100W
• Stereo, 8 ohms (per ch.): 1200W
• Bridge-Mono, 8 ohms: 4200W
• Bridge-Mono, 4 ohms: 6000W

• Input EQ: 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
• Crossover Filters: Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ±15 dB bandpass gain and polarity control.
• Output EQ: 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
• Delay: for signal alignment of driver; 50 mS of total delay.
• SubHarmonic Synth: takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
• Peak x Plus Limiter: user defeatable limiter that allows users to control Threshold, Attack, and Release times.
• Presets: 30 total presets, 29 of which are user-definable.

• Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
• Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, -1 dB
• Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 103 dB (A weighted)
• Total Harmonic Distortion (THD): <0.5%
• Damping Factor 20 Hz to 1 kHz: >500
• Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db
• Input Impedance (nominal): 20k ohms balanced, 10k ohms unbalanced
• Maximum Input Signal: +22 dBu typical
• AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
• AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per channel): 15.3A; no more than 180W at idle
• Operating Temperature: 0C to 40C at 95% relative humidity (non-condensing)

• Level: two front-panel rotary level controls, one for each channel
• Power Switch: On/Off switch applies AC power to the amplifier
• Sel/Prev/Next Buttons: three buttons near the LCD screen that are used to access menu items and front panel lockout
• LCD Screen: backlit liquid crystal display that shows preset and processing status

• Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
• -10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.
• -20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip.
• Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
• Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
• Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
• Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power

• Input Connectors: XLR, one per channel
• Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
• Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).
• HiQnet USB Connector: Type B, connects to HiQnet network.

• Chassis: Steel
• Front Panel: Cast-aluminum
• Cooling: Proportional speed fan with front-to-rear airflow.
• Dimensions: 19" (W) x 3.5" (H) x 16.2" (D)
• Net Weight: 24.0 lb. (10.9kg)
• Requires 220V outlet or adaptor