Yamaha MSR100 / MG82CX PA Package

Yamaha MSR100 / MG82CX PA Package Specifications:

• Total Harmonic Distortion: Less than 0.1 % (THD+N) 20Hz-20kHz@ +14dBu (ST OUT)
• Frequency response: 0, +1, -3dB 20Hz-20kHz @ +4dBu (ST OUT)
• Hum & Noise*: -128dBu equivalent input noise/ -100dBu residual output noise 20Hz-20kHz, Rs = 150 Î, Input Gain = Maximum-128dBu Equivalent Input Noise/
• -98dBu Residual Output Noise
• 20Hz-20kHz, Rs = 150 Î,
• Input Gain = Maximum

• MIC: 4,
• Line: 2 mono + 4 stereo,
• Ch Insert: 2
• Return: 1 stereo
• 2TR IN: 1 stereo
• ST: 1

• Effect Send: 1
• Ch Insert: 2
• REC: 1 stereo
• Monitor: 1 stereo
• Phone: 1
• Crosstalk**: -70dB @ 1kHz
• Phantom Power: + 48V

• CH 1-2 and
• CH 3/4-5/6,
• 80Hz, 12dB/oct

• High: 10kHz: shelving
• Mid: 2.5kHz: peaking
• Low: 100Hz: shelving
• CH EQ (Stereo) ±15dB (Max.)***:
• High: 10kHz: shelving
• Mid: ”
• Low: 100Hz: shelving
• Compressor (COMP): Control x 1 (Gain/Threshold/Ratio), CH 1-2
• Internal Digital Effect: 16 Program, Parameter control Foot Switch (Digital Effect, on/off)

• 2 x 7 points LED meter (PEAK, +6, +3, 0, -5, -10, -20dB)
• PEAK lights if the signal comes within 3dB of the clipping level.
• PEAK Indicator: Red LED turns on when post EQ (ST CH: or post Mic HA) signal reaches -3dB below clipping (17dBu)
• Power Supply Adapter: PA-10: AC 38VCT, 0.62A, Cable Length = 3.6m
• PA-20: AC 35VCT, 0.94A, Cable Length = 3.6m
• Power Consumption: 21W
• Dimensions (WxHxD): 256.6mm x 62.2mm x 302.5mm
• Net weight: 1.6kg
• *Hum & Noise are measured with a 6dB/octave filter @ 12.7kHz; equivalent to a 20kHz filter with infinitedB/octave attenuation.
• **Stereo L/R, CH 1-2, PAN panned Hard left or right @1kHz.
• ***Turn over /roll-off frequency of shelving: 3dB below maximum variable level

• Speaker type: 2-way bass reflex powered speaker
• LF: 8" cone
• HF: 1" compression driver
• Frequency response: 55Hz-20kHz (-10dB)
• Maximum SPL: 112dB (1m)
• Dispersion 90 deg. H x 40 deg. V
• Maximum Output Power: 100W at 1kHz
• THD=1%, RL=6
• Crossover Frequency: 4kHz
• Input Sensitivity Input 1: -50dB*/+4dB* (with select SW)
• Input 2 & 3: -10dB*
• Input Impedance LINE 1 & 2 & 3: 10k
• Link Out -10dB*/ 10k
• Controls Level Control INPUT 1 & 2 & 3, Master Level
• EQ Low: +/-3dB at 60Hz, High: +/-6dB at 10kHz
• Power Switch ON/OFF
• Connectors Input 1:
• Input 2&3:
• Link Out: XLR-3-31 (balanced)
• Phone (unbalanced)
• Phone (unbalanced)
• Indicator Green LED: Power on, Red LED: Clip
• Dimensions
• (W x D x H) 10-7/8"W x 10"H x 18"D
• Weight: 24lb.

• Element: Moving coil dynamic
• Polar pattern: Unidirectional
• Frequency response: 70Hz ” 12.000Hz
• Open circuit sensitivity: -52dB (2.5 mV)
• Impedance: 500 Ohms
• Switch: On/off
• Weight: 329 grams (11.6 oz.)
• Dimensions: 178.3mm (7.02") length, 56.3mm (2.22") body diameter
• Output Connector: Integral 3-pin XLR M-type
• Accessories: Slip-in stand clamp for 5/8" ” 27 threaded adaptor